ITI FITTER FIRST YEAR 2019 THEORY QUESTIONS PAPER SOLVE

ITI FITTER FIRST YEAR 2019 THEORY QUESTIONS PAPER SOLVE

Iti fitter first year 2019 theory questions paper solve.Fitter trade in ITI is one of the most popular trade and its course is of 2 years. In which there is a semester system, there are 4 semesters and there is an examination after every six months. In this post, in this post you will be given a question paper of the first semester, in which you will be given many important questions and their answers, and in the second semester, the question answer will be given to you. You will find them on the website, read them too and try to solve them. Iti fitter first year 2019 theory questions paper solve.

आईटीआई में फिटर ट्रेड बहुत ही पॉपुलर ट्रेड में से एक है और इसका कोर्स 2 साल का होता है. जिसमें सेमेस्टर सिस्टम होता है वहां पर 4 सेमेस्टर होते हैं और हर छह महीने बाद परीक्षा होती है आज की इस पोस्ट में आपको फर्स्ट सेमेस्टर का क्वेश्चन पेपर दिया जाएगा जिसमें आपको काफी इंपोर्टेंट क्वेश्चन और उनके आंसर दिए जाएंगे और दूसरे सेमेस्टर के क्वेश्चन आंसर आपको हमारी वेबसाइट पर मिल जाएंगे अब उन्हें भी पढ़ कर देखिए और इन्हें हल करके देखिए

1] The bench vice spindle is made of

A) Mild steel
B) Cast iron
C) Tool steel
D) Bronze

... Answer is A)
Mild steel

2] In a metric micrometer, a complete revolution of thimble advances

A) 0.01mm
B) 0.25 mm
C) 0.50 mm
D) 1.00 mm

... Answer is C)
0.50 mm

3] The peen of a straight peen-hammer is

A) Angular to the handle
B) Straight to the handle
C) Cross to the handle
D) Bent towards the handle

... Answer is B)
Straight to the handle

4] Which one of the following types of hammers is used for forming a rivet head by spreading the shank of the rivet?l

A) Ball peen hammer
B) Cross peen hammer
C)Straight peen hammer
D) Soft hammer

... Answer is A)
Ball peen hammer

5] Steel rule is made of .

A)Brass
B)Zinc
C)Stainless steel
D) Cast iron

... Answer is C)
Stainless steel

6] Which of the following is an indirect measuring tool?

A) Inside caliper
B)Vernier caliper
C)Universal bevel protractor
D) Inside micrometer

... Answer is A)
Inside caliper

7] Fine facing is done by feeding the tool

A) From centre to the periphery the job
B)From Either periphery to the centre of the job
C)Either (a) or b)
D) Neither (a) nor b)

... Answer is B)
From Either periphery to the centre of the job

8] While step turning, it is preferred to turn first

A) Small diameter step
B)Large diameter step
C)Either (a) or b)
D) Neither (a) nor b)

... Answer is B)
Large diameter step

9] Which among the following is the cause for Incorrect pitch of thread during thread cutting with single point tool

A) incorrect selection of change gears
B)Lead screw worn out
C)Half nut worn out
D) any of these

... Answer is D)
any of these

10] Which one of the following operations is NOT done on a workpiece held in between centres

A)Knurling
B)Undercutting by plunging
C)Thread cutting
D) Parting off

... Answer is D)
Parting off

11] Which one of the following diameters of the workpiece should be turned before cutting diameter external threads

A) Major diameter
B)Core diameter
C)Pitch diameter
D) Head diameter

... Answer is A)
Major diameter

12] What is the trouble when grinding wheel fails to cut in a grinding machine

A) Grinding wheel's grade is too soft
B)Grinding wheel is glazed
C) Grinding wheel is not securely
D) mounted onspindle

... Answer is B)
Grinding wheel is glazed

13] Which one of the following is used to hold cylindrical rough casting for turning

A)Three-jaw chuck .
B)Four-jaw chuck
C) Collet chuck
D) Magnetic chuck

... Answer is B)
Four-jaw chuck

14] The included angle of live centre nosec is

A) 30°
B)45°
C) 60°
D) 90°

... Answer is C)
60°

15] The size of three-jaw chuck is specified by

A) The size of each jaw
B)The thickness of each jaw
C) The diameter of the body of the chuck
D) Width of the body the chuck

... Answer is C)
The diameter of the body of the chuck

16] An angular workpiece is to be faced. It should be mounted

A) In a three-jaw chuck
B)In a collet
C) Between centres
D) On a façe plate

... Answer is D)
On a façe plate

17] Low helix angle drills are preferred for drilling holes in

A) Plastics
B)Copper
C) Cast steel
D) carbon steel

... Answer is C)
Cast steel

18] A dril for drilling deep holes in aluminium should have

A) High helix angle
B)Taper shank
C) Small point angle
D) No slip

... Answer is A)
High helix angle

19] Bench vice is also called as

A) Bench work vice
B)Engineers vice
C) Machine vice
D) Fitter vice

... Answer is B)
Engineers vice

20] In a vernier caliper main scale reading 40 mm, vernier division coinciding with the main scale is the 28 division, then the reading will be.

A)40.46mm
B)40.56 mm
C) 40.28 mm
D) 40.00 mm

... Answer is B)
40.56 mm

21] Drilling machine in which more than one drill used in the same head is

A) sensitive drilling machine
B)Pillar drilling machine
C) Radial drilling machine
D) Multi spindle drilling machine

... Answer is D)
Multi spindle drilling machine

22] The grade of a file is determined by

A) Length of the file
B)Width of the file
C) The gap between the
D) The grade of the metal used

... Answer is C)
The gap between the

23] The commonly used thre point internal micrometers have a least count of

A)0.006 mm
B)0.005 mm
C) 0.002 mm
D) 0.001 mm

... Answer is D)
0.001 mm

24] The purpose of tempering the hardened steel component is for,

A) Increasing its hardness
B)Reducing its brittleness
C) Increasing its ductility
D) Increasing its toughness

... Answer is B)
Reducing its brittleness

25] Which one of the stake is used to make sharp bends and folding straight edges of sheet metal?

A) Funnel stake
B)Hatchet stake
C) Creasing iron stake
D) Half moon stake

... Answer is B)
Hatchet stake

26] The function of flux during soldering is

A) To prevent Icorrocinn
B)To promote wet eurface
C) To avoid porosity in solder
D) To remove oxidese from the soldering surface

... Answer is D)
To remove oxidese from the soldering surface

27] In which colour the welding oxygen cylinders are painted?

A) Red
B)Maroon
C) Black
D) Brown

... Answer is C)
Black

28] The most commonly used rivet is

A) Round head
B)Pan head
C) Countersunk
D) Flat head

... Answer is A)
Round head

29] Which accessory is used for protecting the eyes while chipping the slag or grinidng the job?

A) Plain screen
B)Hand screen
C) Goggle
D) Helmet screen

... Answer is C)
Goggle

30] Which angle can be chęcked byTry square.

A) 60
B)30
C) 90
D) 45

... Answer is C)
90

31] Benefits of the 5S systems are ………………….

A) Increase the cleanliness
B)Increase the productivity
C) Increase the production rate
D) Maintain the production

... Answer is B)
Increase the productivity

32] The clearence angle of a drill is between-

A) 8 to 12
B) 3 to 5
C)15 to 20
D) 15 to 20

... Answer is A)
8 to 12

33] The angle of twist drill is ………………….

A) 1210
B)118°
C) 125
D) 140°

... Answer is B)
118°

34] The carriage of lathe is situated at the-

A)Middle of the bed
B)Bottom of the bed
C) Right hand of the bed
D) None of these

... Answer is A)
Middle of the bed

35] The symbol conventionally used for resinoid bond is

A) V
B)R
C)B
D) E

... Answer is C)
B

36] The taper provided in nose of the tailstock spindle is

A) Morse taper
B)Jarno taper
C) Metric taper
D) Brown& sharp taper

... Answer is A)
Morse taper

37] Vernier depth gauge is used for measuring

A) External dimensions
B)Internal dimensions
C) Step depth of blind holes
D) Pitch diameter

... Answer is C)
Step depth of blind holes

38] Ratchet stop in the vernier micrometer helps to:-

A) Control the pressure
B) Lock the spindle
C) Adjest Zero error
D) Hold the work piece

... Answer is A)
Control the pressure

39] Which one contains higher percentage of carbon?

A) High carbon steel
B) Low carbon steel
C)Tool steel
D) Cast iron

... Answer is D)
Cast iron

40] Size of taping drill for M 10 X 1.5 Thread is_

A) 8.40 mm
B) 8.20 mm
C) 9.10mm
D) 7.80 mm

... Answer is A)
8.40 mm

41]Spot facing is done to_

A) Deburr the mouth of the drilled hole
B) Make surface flat so that bolt head can take proper seat
C) Give fine finish to the drilled hole
D) Enlarge the existing hole

... Answer is B)
Make surface flat so that bolt head can take proper seat

42] The main function of flux is_

A) To avoid oxidation
B)To join metal
C) To increase temperature
D) None of these

... Answer is A)
To avoid oxidation

43] What will be the effect if drill point is not in centre?

A) Rough holes
B)Broken drills
C) Overheated drills
D) oversized holes

... Answer is D)
oversized holes

44] Which one of the following parts of a universal surface gauge helps to draw parallel lines along a datum edge

A)Fine adjusting screw
B)Guide pins
C) Base
D) Rocker arm

... Answer is B)
Guide pins

45] Which of the following is not the part of a combination set?

A)Stock
B)Protractor head
C) Square head
D) Centre head

... Answer is A)
Stock

46] Shank diameter of a rivet is usually determined by

A)Ohm's law
B)Sine rule
C) Unwin's formula
D) Vernier caliper

... Answer is C)
Unwin's formula

47] During marking, the reference surface is provided by

A)Sketch of the job
B)Workpiece
C) Marking off table surfac
D) Surface gauge

... Answer is C)
Marking off table surfac

48] The tool, Which is used for laying out large circle is

A)Trammel
B)Divider
C) Jenny caliper
D) Scriber

... Answer is S)
Trammel

49] What is the function of a pipe vice?

A)Grips the work at four point
B)The screw is vertical
C) The movable jaw move svertically
D) All of these

... Answer is A)
Grips the work at four point

50] Handle of hammer is made of

A)Hard wood
B)Soft wood
C) Elastic wood or bamboo
D) Rubber

... Answer is C)
Elastic wood or bamboo